Dillon-precision XL 650 Uživatelský manuál

illonrecisionProducts, Inc.Manufacturers of The World's FinestLoading EquipmentXL 650Instruction ManualVersion 6.1

11Note: One end of the casefeed tube is beveled and one end is squared off.Insert the squared end of the tube (down) into the top of the casefeed adap

12PISTOL SECTION –Toolhead Set UpTo set up the toolhead you’ll need to haveempty brass, bullets, primers and powderon hand. (For your convenience Dill

13FIG 33FIG 34 1. Use a 5/32” Allen wrench to loosenthe two collar clamp screws andremove the powder die FIG 33 & 34.FIG 352. Screw the powder die

14and small powder bar, on the other hand,are standard equipment and are includedwith every XL 650. All powder measuresare shipped with small powder b

15FIG 446. Once you’ve achieved the desiredamount of bell – with the case inStation 2, raise the platform. Run thelockring down hand tight FIG 44.FIG

16FIG 52G. Station 3 – Installation of the Powder Check System FIG 52:Note: The powder check system does not guarantee the accuracy of the pow-der ch

17FIG 606. FIG 59 Screw the 10-24 screw andnut fully into the rod. Raise the plat-form. Unscrew the 10-24 screw untilit contacts the edge of the platf

18FIG 65I. Station 4 – Seating Stems for pistol FIG 65All pistol seating dies come with inter-changeable seating stems. The seating stemyou should use

FIG 70Note: FIG 70 When adjusting the crimpdie it is important to know what tolook for. Check that the crimp: LooksOK, allows your firearm to function

RIFLE SECTION – Toolhead Set UpTo set up the toolhead you’ll need tohave your empty brass on hand. For yourconvenience Dillon Precision offers a wide

Dillon Precision Products, Inc.8009 E. Dillon’s WayScottsdale, AZ 85260(480) 948-8009FAX (480) 998-2786Web Site: www.dillonprecision.comE-mail: dillo

FIG 78FIG 79C. Station 1 – Installation and adjustment of the siz-ing/decapping die FIG 78:Warning: Never attempt to de-prime a liveprimer, an explosi

D. Station 1 – The decapping assembly FIG 78:Dillon decapping assemblies are madewith replaceable decap pins. One extra pinis included with each sizin

FIG 90In FIG 90 are two examples of the manypowder funnels available for the XL 650.On the left is a typical pistol caliber fun-nel. On the right, a r

FIG 94To adjust the powder die/powderfunnel:1. Drop a lubricated case into the case-feed funnel and cycle the handle. Thecase should now be in the she

FIG 100H. Station 2 – Installation of the failsafe rod assembly FIG 100:The purpose of the powder measure fail-safe rod is to return the powder bar to

3. Run the lockring down. Using a 1-1/8” wrench snug the lockring. FIG 107FIG 1084. Remove the 10-24 screw and nutfrom the black push rod FIG 107 and

FIG 114If the bullet you’re using doesn’t have acannelure, then you’ll need to refer toyour reloading manual for the suggestedOAL. The purpose of the

turning it counter clockwise and tryagain.6. Screw the seating stem down 1/2 turnat a time FIG 118.FIG 1197. Repeat as necessary until the correctover

Final AssemblyFIG 122FIG 1231. The Primer MagazineThe XL 650 comes equipped with anautomatic primer system.The XL 650’s auto-matic primer system is pr

FIG 1283. Installation of the Locator Buttons FIG 128:Install the three brass locator pins in theshell platform at stations 3, 4 and 5. Thesepins reta

Page #Mandatory Safety Measures 5Getting Started 61. Unboxing your machine 62. Mounting your XL 650 73. Initial Set-Up 7A. Installation of Handle 7B.

31properly adjust the powder bar. Dillon Precision Products offers two types of scales FIG 134. On the right, and electronic scale, and on the left, a

FIG 139A. Installation and adjustment of the powder check rods FIG 139:1. Remove the powder check rods fromthe bag FIG 139. The three rods fitdifferen

Note: If the buzzer to the powder check system goes off, stop loading and check the powders weight with the scale. The primer warning buzzer and the p

Add some empty cases to your casefeederand turn the unit “on”. The motor will rununtil the clear casefeed tube fills and then itwill automatically shu

1. How to use the CaliberConversion Chart:To explain the Caliber ConversionChart we are going to compare the pistolcaliber of .38 Spl. to the rifle ca

FIG 1592. Using a 1/4” Allen wrench removethe shellplate bolt FIG 159.FIG 1603. Swing the ejector wire out of the wayand remove the shellplate. Be sur

FIG 1653. Rotate the primer system upsidedown. Using an 1/8” Allen wrenchunscrew the primer support shimscrew and remove the primer supportshim FIG 16

FIG 1723. Swing the ejector wire back to itsoriginal position over the shell-plate and insert the shellplate boltFIG 172. 4. Using a 1/4” Allen wrench

FIG 1791. Remove the casefeed tube FIG 179.FIG 1802. Remove the casefeed adapter FIG180.FIG 1813. To replace the casefeed arm bushingfirst raise the p

FIG 187Step 15) Change out the casefeed disc FIG 187:Change the casefeed disc only if your cal-iber conversion requires it. 1. Grip the casefeed plate

Reloading small arms ammuni-tion involves the use of highlyexplosive primers and powder.Handling these materials is inher-ently dangerous. You should

FIG 193Note: The objective here is that – at the point the case becomes fully insert-ed into shellplate (with the handle against its full aft stop) –

6. a) Installation of the large powderbar – slide the large powder bar intothe powder measure body.b) Installation of the small powderbar – slide both

Trouble ShootingDies Too ShortA. Need Dillon die lockrings (14067).1. Three extra come with the machine.2. Threadaphobia (fear of too few threads) can

4. Point of decap pin is squared off not rounded (pin gets stuck in anvil and pulls primer back into primer pocket).5. Berdan primed brass.a. Berdan p

Station 4 - Bullet SeatingA. Erratic seating depth of the bullet.1. Variations of less than 20 thou-sandths of an inch are due to varia-tions in cases

46650 Caliber Conversion Chart - PistolTo order a complete conversion use the 5 digit number to the right of the caliber listing.To order individual p

47650 Caliber Conversion Chart - RifleTo order a complete conversion use the 5 digit number to the right of the caliber listing.To order individual pa

48650 Caliber Conversion Chart - RifleTo order a complete conversion use the 5 digit number to the right of the caliber listing.To order individual pa

491234657810109CompletePowder MeasureAssemblysee page 56 formore detailsToolheadAssemblysee page 53for more detailsPlatform Assemblysee page 54for mor

502315162417181414141311122125262722191920Casefeed Body Assemblysee page 52 for more detailsMachine Assembly11 13830 Mainshaft Pivot Pin12 13789 Mains

6GETTING STARTED1.Unboxing Your Machine:After opening the box, check the con-tents against the list below. If any items aremissing or damaged, call us

51Lower Machine Assembly1 13470 Chute/Bin Mount2 13839 Blue Cartridge BinItems A, B, and C included in optionalHardware Mounting Kit, #16600.21ABCFram

1 16652 Platform2 14013 8-32x3/8 Cap Screw3 16210 Primer Chute4L 21380 Rev B Seater Assembly, Large4S 21381 Rev B Seater Assembly, SmallCasefeed Body

53Primer Early WarningBuzzer Assembly #20302Toolhead Assembly &Orientation#13863 - XL650 Toolhead1 13957 Magazine Shield Cap2L 22033 Primer Magazi

34pistolsiderifleside6161711102218192023242621111131415259872527293028281, 2 97082 Case Insert Slide & Slide Cam (1)3 13418 Shellplate Bolt4 13298

Primer System Assembly#20982 Large, #21065 Small1 13957 Magazine Shield Cap2 13964 10/24x1/4 BH Screw3 13367 Failsafe Bracket4 13862 Primer Disc Pin5

56138822227313691137931480813940138451387197034140411390413939140371406720064*137821634014202138481389320062213532006313426 * Powder Funnel, .22 cal r

57HIGHOFFLOW13400 Casefeed Bowl13473 Motor13494 Casefeed Funnel - part, Small22173 Casefeed Funnel Assembly22174 Belted Magnum/.45-70 Casefeed Funnel

5815139211019177AAA BatteryIncluded161420182181461211543Powder CheckSystem Assembly#210441 14067 Die lockring2 13990 Powder Die3 21372 Powder Check Ro

59NOTES:

72.Mounting your XL 650:A. Locate a sturdy bench at least 24” wide and 14” deep, with 44” of overhead clearance. We suggest a minimum of 1” plywood or

FIG 5Operate the handle slowly to ensure thatthe machine operates smoothly. Make surethat the handle and the crank completelyclear the bench. Contact

9E. Installation of the Optional Casefeeder FIG 12:FIG 121. Remove the casefeed parts bagfrom the casefeed bowl and removethe casefeed assembly from t

10To Install the casefeed funnel adapterFIG 18:FIG 18Remove the screws that attach the clearcasefeed funnel. Slide the front cover downa bit, and slip